Tees

• 90° Tee and Grease Duct Tee
• 45° Tee
• Double 45° Tee

90° Tee (T90) and Grease Duct Tee (GT90)

For connection of vertical and horizontal lengths. A tee cap (TC) or drain-tee cap (DC) may be used to block one of the cleaning or drainage openings.

K=1.25

		I.D. A B in mm in mm in mm 6 152 17.750 451 10.000 254 8 203 19.750 502 11.000 279 10 254 21.750 552 12.000 305 12 305 23.750 603 13.000 330 14 356 25.750 654 14.000 356 16 406 27.750 705 15.000 381 18 457 29.750 756 16.000 406 20 508 31.750 806 17.000 432 22 559 33.750 857 18.000 457 24 610 35.750 908 19.000 483 26 660 37.750 959 20.000 508 28 711 39.750 1010 21.000 533 30 762 41.750 1060 22.000 559 32 813 43.750 1111 23.000 584 34 864 45.750 1162 24.000 610 36 914 47.750 1213 25.000 635 38 965 49.750 1264 26.000 660 40 1016 51.750 1314 27.000 686 42 1067 53.750 1365 28.000 711 44 1118 55.750 1416 29.000 737 46 1168 57.750 1467 30.000 762 48 1219 59.750 1518 31.000 787

45° Tee (T45)

For connection of vertical and horizontal lengths at a 45¾ angle. It provides low resistance to facilitate gas
discharge. A tee cap (TC) or drain-tee cap (DC) may be used to block one of the cleaning or drainage openings.

K=0.4

		I.D. A B C in mm in mm in mm in mm 6 152 26.235 666 6.993 178 19.243 489 8 203 29.064 738 7.407 188 21.657 550 10 254 31.892 810 7.821 199 24.071 611 12 305 34.721 882 8.235 209 26.485 673 14 356 37.549 954 8.649 220 28.899 734 16 406 40.377 1026 9.064 230 31.314 795 18 457 43.206 1097 9.478 241 33.728 857 20 508 46.034 1169 9.892 251 36.142 918 22 559 48.863 1241 10.306 262 38.556 979 24 610 51.691 1313 10.721 272 40.971 1041 26 660 54.520 1385 11.135 283 43.385 1102 28 711 57.348 1457 11.549 293 45.799 1163 30 762 60.176 1528 11.963 304 48.213 1225 32 813 63.005 1600 12.377 314 50.627 1286 34 864 65.833 1672 12.792 325 53.042 1347 36 914 68.662 1744 13.206 335 55.456 1409 38 965 71.490 1816 13.620 346 57.870 1470 40 1016 74.319 1888 14.034 356 60.284 1531 42 1067 77.147 1960 14.448 367 62.698 1593 44 1118 79.975 2031 14.863 378 65.113 1654 46 1168 82.804 2103 15.277 388 67.527 1715 48 1219 85.632 2175 15.691 399 69.941 1777

Double 45° Tee (DT45)

Used to connect two systems together with a minimum resistance to flow. A tee cap (TC) or drain-tee cap (DC) may be used to block one of the bases of the piece, for cleaning or drainage. Specify the diameters of inlets and outlets of the fitting.

K=0.4